How to Shut Off the Water at Home Before a Plumbing Fix

To shut off water at the meter, lift the lid of the box at the curb or in the front planting strip, find the valve on the house side of the meter, and turn it a quarter turn so the handle sits crosswise to the pipe. If you can reach the main valve on the house itself, use that one first. It is easier to reach, and it is yours to operate.
Do this walk-through once on a dry day, before anything is leaking.
Shut off water at the meter (the street box)
The meter box is a concrete or plastic box set in the ground, usually near the curb or at the edge of the front yard. The lid is often heavy and packed with dirt. In LA, Santa Ana dust and sprinkler overspray turn that dirt into a crust.
What you need:
- A flat screwdriver to lift the lid from the slot
- Work gloves
- A long stick or old paintbrush to clear the box
- A water meter key or a large adjustable wrench
Steps:
- Pry the lid up with the screwdriver in the lid's slot. Keep your fingers out from under the edge.
- Sweep the box with the stick before you reach in. Spiders like these boxes, black widows included.
- Find the meter, which has a dial and a small spinning indicator. Locate the valve on the house side of it, between the meter and your yard line.
- Turn the valve with the key or wrench. On a quarter-turn ball valve, handle parallel to the pipe means open and handle crosswise means closed.
- Open one faucet inside the house. It should run for a few seconds and stop.
The meter and the utility's own valve belong to the utility (LADWP in most of the city). Use only the valve on your side, and do not try to remove or loosen anything on the meter. If the valve will not turn with firm, steady pressure, stop. Forcing a buried valve can snap the stem and leave you with no shutoff at all.
Shut off water at the house main
The house main is the valve you want in most emergencies. Where it hides depends on the house.
- Stucco homes: look on the front or side wall, often within a few feet of a hose bib, where a pipe comes up out of the ground.
- Slab-on-grade homes: there is no basement, so check the garage wall, usually near the water heater, and the side yard.
- Pre-1950 bungalows and duplexes: look in a hall closet, a service porch, or a small access panel in the plaster. Plaster-and-lath walls are brittle, so do not pry at a panel without looking for hinges or screws first.
- Hillside homes: a bell-shaped brass pressure regulator often sits right after the main. The shutoff is the valve just before it.
Two valve types turn up:
| Valve type | How it works | What to know |
|---|---|---|
| Ball valve (lever handle) | Quarter turn | Crosswise to the pipe is closed |
| Gate valve (round wheel) | Several turns clockwise | Hard-water scale freezes the stem; turn gently and never force it |
A gate valve that has not moved in ten years may stick, or may drip from the stem once you turn it. If it drips, snug the packing nut behind the handle about an eighth of a turn. If it will not close fully, it is time to replace it, and that needs a pro with the water off at the meter.

Shut off water at the toilet and under sinks
For a single toilet or faucet, skip the main. The fixture has its own stop valve.
Toilet: the stop is on the wall or floor, left of the tank. Turn the oval handle clockwise until it stops. Flush once to empty the tank, and you can work on the fill valve or supply line. The supply line is usually a 3/8" tube that connects to the 7/8" fill valve nut under the tank.
Sinks: hot is on the left, cold on the right. Most are multi-turn stops, and a few newer ones are quarter-turn.
Three things to know about stops in LA houses:
- Hard water crusts them. Chrome stops that have sat for years may not close fully, or may leak at the stem the first time you turn them. Keep a towel and bucket under the valve.
- Older homes may have none. In some 1920s–40s houses, the sink pipe runs straight into the wall with no stop. Your only shutoff is the main.
- A stop that drips after closing is not holding. Do not start the repair. Go back and close the main.
Which valve to close for which problem
| Problem | Close this first | Then |
|---|---|---|
| Toilet running or overflowing | Toilet stop | Lift the tank lid and hold the float up if it is still filling |
| Sink supply line spraying | That sink's stop | If the stop fails, close the main |
| Burst pipe in wall or ceiling | House main | Turn off the water heater power or gas |
| Water heater leaking | Cold inlet valve on top of the heater | Close the main if it continues |
| Unknown leak, wet spot on slab | House main | Run the meter test below |
| Hose bib dripping inside wall | House main | Shut off the interior bib stop if one exists |
The meter test. With every fixture off, look at the meter's small low-flow indicator. If it spins, water is moving somewhere. Close the house main. If the indicator stops, the leak is inside the house. If it keeps spinning, the leak is on the yard line between the meter and the house. Slab-on-grade leaks often show up as a warm spot on the floor or a hissing sound at night.
Before you drain or turn back on:
- Switch off an electric water heater at the breaker, or set a gas heater to pilot, before you drain lines. A heater firing on an empty tank can damage itself.
- Reopen the main slowly. Opening it fast can hammer old pipes and blow out a worn washer.
- Open the highest faucet in the house first to let air out, then the others.
- Dry wet drywall, carpet and plaster promptly. The EPA recommends drying wet materials within 24 to 48 hours to limit mold.

When to call a pro
Handle yourself: closing a toilet or sink stop, closing a working main, running the meter test, and swapping a braided supply line once the water is off.
Call a pro when:
- The main or meter valve will not turn or will not seal.
- Any stop valve leaks from the stem or body after you close it.
- Water is coming from inside a wall, ceiling, or slab.
- You need to replace a stop or main valve, which means working on live supply pipe.
- The meter indicator keeps spinning with the house main closed.
At STATOX, we ask for a photo first, then give you one written price for the job. When we arrive, we find your main, confirm it holds, and check the stops at the fixture before we open anything. If a valve will not close, we tell you before we start. You can send a photo for a written quote, or see how our plumbing fixes service works.
FAQ
How do I shut off water at the street?
The street box is the same meter box described above. Lift the lid, clear it, and turn the valve on the house side with a meter key or adjustable wrench. If the valve does not move with steady pressure, do not force it. Contact LADWP, because the utility owns the meter and the connection.
Can I shut off the water at the house if I cannot find the main?
Look near the hose bib, in the garage near the water heater, in a hall closet, or at a service porch panel. Follow the cold line from the water heater back toward where it enters the house. If you still cannot find it, the meter box is your fallback.
Which way do I turn the valve?
Clockwise closes a wheel or gate valve. On a quarter-turn lever, crosswise to the pipe is closed. Toilet and sink stops also close clockwise.
Why is the water still running after I closed the valve?
Water already in the pipes will drain out through the open fixture. If it keeps flowing for more than a minute or two, the valve is not sealing, and you need to close the next valve upstream.
How often should I test my shutoff valves?
Once or twice a year, turn each stop and the main closed and open again. Hard water scale sets in on valves that never move. Do this when you are not in an emergency, and keep a towel handy.
Sources
- EPA WaterSense: Fix a Leak Week
- EPA: A Brief Guide to Mold, Moisture, and Your Home
- LADWP
- California Contractors State License Board: Hire a Contractor
STATOX Handyman Service · Send a photo · +1 (820) 200-4919


